ㅇKey Features RF Front-End - Frequency : C-Band - Tx Power : +27 dBm(0.5 W) , Rx Range : -10 ∼ -100 dBm - Rx Sensitivity : -95 dBm@2 MHz Baseband & Modem - Downlink : 2.4 Mbps / Uplink: 8 kbps - QPSK waveform and CTC Forward Error Correction Anti-Jamming / Anti-Spoofing / Video CODEC - Anti-Jamming Capability using DSSS - Anti-Spoofing Capability by AES-256/ ARIA-256 Encryption - Support H.264 / up to 1920x1080x30f Interface - 10/100 Base-T Ethernet x1, RS-422 x1, RS-232 x2 - 3G-SDI Digital Video IN/OUT Interface - Limited Discrete I/O (1PPS/sync_in, reset_in, status_out) ㅇQuality and Certification - MIL-STD-810G - MIL-STD-461F

The aerospace industry has brought one of humanity's oldest dreams to life, a dream that seemed out of reach for so long : the ability to fly, to travel among the stars. Symbolizing freedom, discovery and travel, airplanes bring people together and foster cultural exchange.

Our technology and quality have been recognized internationally and regionally as we supply products manufactured based on AS9100, NADCAP special process approval to global companies lockage in domestic and overseas.

The SDT F 16 Combat Training Pod is mounted on F-16 and similar air platforms in an external pod, and ensures efficiency in exercises and in the provision of air-to-air and air-to-ground tactics training to pilots. SDT F - 16 Combat Training Pod features advanced air-to-air and air-to-ground combat training capabilities, such as real-time autonomous position generation, weapon simulation and real-time hit/miss notification, thanks to its long-range and high-speed RF data link and integrated processors. The system has mission planning, live monitoring, debriefing and analysis/evaluation features. The SDT F 16 Combat Training Pod enables training in real flight conditions and in multi-threat/target environments. Its high-speed data link and modular design mean that the System is also a Live-Virtual-Constructive (LVC) training infrastructure.

Our LiDAR uses a custom-designed laser that separates 1064 nm and 532 nm wavelengths from a single source, with two dedicated receivers capturing each set of data independently. Inside the system, the linear laser beam is refracted at a 10-degree angle through a prism to enable circular scanning. An RF module is also integrated for real-time equipment status monitoring. From circuit board design to component selection, every part of this system was developed in-house by multiple institutions. As a result, we have successfully eliminated reliance on foreign technology.

With a peak torque of >200Nm / 1770 lbf-in and a rated torque of 80Nm / 708 lbf-in, the fully redundant DA 58-D is the strongest, electromechanical, fully integrated (actuator control electronics, position sensing, motor and drivetrain in one housing) actuator in the market. Besides the well-proven redundant RS 485 interface, the DA 58-D also features a redundant CAN bus interface. The DA 58-D has been developed for applications with the highest reliability demands. The redundant – two channel – design of the actuator allows continuous operation even if one of the two channels has failed. All major components such as the electric motors, control and communication electronics, and power supply are available twice (redundant). The actuator features a triple-redundant position sensor (2 out of 3 voting). Additionally there are several sensors integrated to provide diagnostic information such as current consumption, supply voltage levels and temperature readings. All major components of the actuator are continuously diagnosed by the microcontrollers of the actuator and its health status can be read via the redundant RS485 / CAN interface.

RFcore has been innovating MMIC solutions for phased array system pursuing more ease of use, higher performance, higher level of integration as well as lower cost. We believe that the most suitable way is exploiting properties of God gifted semiconductor Silicon and GaN. We aim at integrating all components of TRM for active phased array on single die and even multi-channel TRM too.

The SWE450S is a rugged 3U VPX fully managed Layer-2/3 Ethernet switch aligned with the compute-intensive SOSA profile, delivering high-performance 25/100 GbE switching and flexible I/O reconfiguration. • High-performance 2 Tbps switch fabric with wire-speed throughput • Front: up to 2x 100 GBASE-SR4 (MPO); Rear: 25/100 GbE KR4, 100/1000 BASE-T, USB-C, RS-232Reconfigurable fat-pipe to thin-pipe ports, speed downgrading capability • Dual-core ARM + OpenWare™ management, sanitization support • SOSA-aligned (SLT3), rugged air- & conduction-cooled options