DA 22-BLDC Brushless Actuator To guarantee maximum safety and reliability, its brushless motor and contactless, wear-free position sensing system makes the DA 22 BLDC immune to wear, vibrations and shock loads. It has especially been designed for usage in harsh environments and for safety-critical applications that require an actuator with high endurance. The conductive aluminum case and the shielded connection cable are reducing the susceptibility to any kind to EMI/RFI noise to the absolute minimum.

Side shells, wing shells and fuselage structures are made of CFK, GFK, aluminium or organic sheets and get connected during production. Sealants are used to seal the connection surfaces. These are usually two-component polysulphides, which have to be applied in different geometries. Typical applications are: Fillet sealings, oversealings, interface sealings and seal caps. Due to their properties, polysulfides require very low pressure and shear handling. The compressibility of the fillers contained in the medium requires a high level of expertise and a coherent overall system from material removal to application. With manual application, long production times and high material ejection have a negative influence on the complete process. Complex quality standards are required due to the risk of human error. With the in-house developments of the vipro-DUOMIX from ViscoTec, this process can be depicted fully automatically. The individual nozzle design is also adapted to each application. The result is a controlled dosage in compliance with the specifications and at the same time the highest repeat accuracy.

An indigenous combat system to be installed on the next-generation Korean Destroyer (KDDX), developed as a localized alternative to the Aegis Combat System. It is a fully integrated software and hardware suite that controls all assets—including power systems, sensors, and weapons—to conduct naval operations. - Compliant with MIL-SPEC standards (shock, vibration, temperature/humidity, EMI/EMC) - Incorporates connector assemblies to enhance maintainability

Engine accessories for Model 250 Rolls-Royce (Allison) gas turbine engines. Bleed Valves, Fuel Controls, Fuel Nozzles, Fuel Pumps, Governors & more.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

- Inspection robot control and damage assessment for robot operators. - Pre-inspection information creation for inspection planning. - A 3D user interface for inspection robot status monitoring. - Damage assessment and result report generation capabilities.

The Haigh-Farr Wraparound™ is a self-contained omnidirectional antenna for cylindrical or conical shaped bodies. A single point feed is used and no external splitters, combiners or cable harnesses are required for installation. The antenna is conformal, and may be mounted flush, or on the exterior of the vehicle. Designs are available from 300 MHz to 13 GHz with typical applications including Flight Termination, GPS, Telemetry, Data Links and Transponder. Multiple antenna elements may be combined within the same physical Wraparound™, providing multi- band capability in a single, compact package. Wraparound™ antennas have been flown on vehicles from subsurface sea to space, including high-mach kinetic kill weapons, high-G projectiles and re-entry vehicles. The Wraparound™ has been qualified for use on several high performance vehicles flown on test and launch ranges throughout the United States and Europe. For high aero-heating applications an ablative heat shield may be added to the antenna for additional thermal protection.

STX Engine produces medium speed engine driven power generation equipment that can satisfy customers 100% by ideally combining medium speed engines, which have been collectively produced at our Changwon factory since obtaining licenses from the mid 1970's from MAN ENERGY SOLUTIONS in Germany and NIIGATA POWER SYSTEM in Japan, with a power generation system designed with rich experience in the area of system engineering. By installing diesel engine power generation equipment in locations across Korea and overseas, such as on islands, remote areas, resorts, etc., where no public power supply is available, as well as industrial complexes and hospitals which require good source of power, and factories receiving expensive public power supply, etc., our customers can confirm the investment effect within a short period of time after experiencing the power supply we make available to them, as well as low installation and operation costs and maximized availability of the equipment.