Engineering Design Assistance Material Research & Development Manufacturing

Our LiDAR uses a custom-designed laser that separates 1064 nm and 532 nm wavelengths from a single source, with two dedicated receivers capturing each set of data independently. Inside the system, the linear laser beam is refracted at a 10-degree angle through a prism to enable circular scanning. An RF module is also integrated for real-time equipment status monitoring. From circuit board design to component selection, every part of this system was developed in-house by multiple institutions. As a result, we have successfully eliminated reliance on foreign technology.

High-Reliability Space-grade SRAM memory : 1. Density : 16Mbit (512k x 32bit) SRAM 2. Package Type : 100 Pin CQFP (Ceramic Quad Flat Package) 3. MIL-PRF-38535 Class V Qualified 4. Operating Temperature : -40℃ ~ +125℃ 5. Radiation : TID > 102 krad, SEL LETth > 80.4MeVcm2/mg@ 85℃

To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

Thermal Battery has high power density, high reliability, wide temperature range (-54°C to +75°C), long shelf life (15 years or more) with short activation time. We service the optimized and customized solutions to the customers worldwide. * Applications - Guided Missiles - Projectiles - Rockets - Bombs, Mines - Decoys

Machine vision system Factory automation Medical imaging systems Robot eyes

ts advanced integrated optics and closed-loop Field Programmable Gate Array (FPGA) electronics deliver much higher accuracy, lower noise and greater efficiency than competing technologies. In addition, the EG-1300 can be calibrated internally for better thermal effect and has both digital and analog outputs, along with separation of the electronics from the FOG’s sensing coil assembly to accommodate the widest variety of installation parameters. Features Fully-integrated optics and electronics Advanced optics and FPGA electronics for higher accuracy, lower noise and greater efficiency Precise navigation (1 mile/hour without GPS) Fast, precise gyrocompassing to 1 milliradian Bandwidth to 500 Hz Separate electronics and sensor modules More economical than competing systems Applications Navigational grade applications Unmanned aerial vehicle (UAV) guidance Missile guidance Aeronautics and aviation Robotics

The QRS116 is a compact angular rate sensor ideally suited for applications in tactical, aerospace and mission-critical instrumentation. The QRS116 features exceptionally low noise, fast start-up, and a simple electrical interface, the QRS116 has no moving parts ensuring long service life and high MTBF. System Performance PARAMETERS SPECIFICATIONS Standard Ranges ±100°/sec Input Voltage + 5 Vdc ±5% regulation Short Term Bias Stability (100 sec at const. temp) 3 deg/hr Output Noise ( DC to 100 Hz) ≤ 0.002°/√Hz* * Values Indicated are for ±100°/sec. Range Features Exceptional Bias Stability Unprecedented Low Angle Random Walk Values Superior Vibration Performance Compact Industry-Standard Package (Same as QRS11) Rugged, Compact Package Integrates easily Applications Tank Turret Stabilization Defense Fixed Wing Defense Helicopter Unmanned Aerial Vehicles UGV – Unmanned Ground Vehicle Platform Stabilization Camera Stabilization Antenna Stabilization ROV – Remotely Operated Vehicle