To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

SeaHFlight is an advanced 2D/3D GIS-based command and control solution engineered for the comprehensive management of low-altitude aircraft, including helicopters, drones, and future UAMs. It provides a complete operational picture, offering full lifecycle management from initial flight planning and real-time monitoring to post-flight performance analysis. Key Capabilities: Unified Situational Awareness: Achieve superior decision-making with a dynamic 2D/3D operational map that visualizes all air assets in real-time. The system integrates crucial data layers, including weather, airspace information, and flight plans. End-to-End Mission Management: Streamline the entire operational workflow, covering everything from flight plan creation and pilot hour management to flight history recording and detailed performance evaluation. Proven Interoperability: SeaHFlight is designed for seamless data integration with key national and military agencies (Army, Police, National Fire Agency, Forest Service). This creates a unified network for complex, multi-agency public safety or defense operations. Future-Ready Platform: Built to manage not only current helicopter and drone fleets but also the next generation of Urban Air Mobility (UAM), SeaHFlight is a scalable, long-term solution for modern aviation.

Vehicle-type RF Jammer Systems provide protection to VIPs and convoys against remote-controlled explosives. These systems create a protective shield through RF broadcasting and neutralize threats activated by radio, mobile phones and wireless remote-controlled devices. Vehicle-type RF Jammer Systems can be easily integrated aboard all kinds of vehicles, and allows for reprogramming against changing situations. Continuous broadband operation Control from hand terminal Module selection Malfunction warning VSWR warning

The VPX power supplies are compliant with VITA 62, MIL-STD-704, MIL-STD-461 and MIL-STD-810 for 28 Vin DC, 270 Vin DC & Universal AC systems. The VPX delivers up to 1000 W and up to 6 outputs with a typical efficiency of 91%. Offered in VITA approved ruggedized 3U and 6U size packages with internal conduction cooling and high speed backplane connectors.

i3system’s line scanning X-ray detector platform, XID-C15DP/XID-C24DC, is a high performance and cost effective solution for dental panoramic, cephalometric applications. i3system’s direct type sensor ensures the most sharp images among the current products in the market. XID series is designed for compact size and easy installation. High DQE(Direct Quant㎛ Efficiency) enables high performance at lower dose of X-ray. Introduction Indirect type X-ray detector uses the scintillator and the photo-diode(CCD or CMOS sensor) for conversion of the X-ray into the light and for taking images espectively. But the light scatters and goes extinct during it passes through the scintillator and reaches to the CCD or CMOS sensor. As a result, it is inevitable to get blurred image. In the mean time, XID C15DP, direct type detector, converts X-rays into electronic signals directly without conversion process of light. Because X-ray is not converted into light, it provides much sharper images than indirect type detector. XID C15DP is designed to compact for easy installation. It provides Gigabit Ethernet port on the detector for easy configuration. Instead of Gigabit Ethernet, camera link or optical interface can be provided according to requirements of users.

Military Parts

The semi-automatic ViscoTec mix-on-demand station is already in successful use as a mobile system. For reliable mixing and dosing of two-component materials, in situ. Two-component materials are commonly processed using premix cartridges, hardener rod cartridges or by mixing two components by hand. The disadvantages are obvious: The risk of human error, enormous material waste and high production costs offer every reason for taking the automated route. With ViscoTec filling stations, epoxy resins, polysulfides and polyurethanes can be removed from larger containers and filled on-demand with the exact quantity required. The dosing is volumetric on a component or a filling container. A typical application is dosing in so-called inserts (thread inserts). The compact arrangement of the components on a mobile frame guarantees the operator maximum flexibility. The design as a stationary system has already been implemented several times.

EFFECTIVE RANGE : 600 m RIFLING : 1:7" Twist, 6 Groove R/H MAGAZINE CAPACITY : 30 rounds