Military Parts

A distributed sensor system based on BOTDA (Brillouin Optical Time Domain Analyzer), capable of detecting structural deformation and external intrusion.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Ultra-High Accuracy MEMS Certus Evo features some of the highest accuracy MEMS accelerometers and gyroscopes currently available. Certus Evo’s inertial performance exceeds some FOG IMUs and is up to 100x smaller and 10x cheaper. Certus Evo is put through Advanced Navigation’s intensive calibration process to provide consistently accurate data over an extended temperature range of -40°C to 85°C. AI-Based Algorithm Certus Evo features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. It was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. Dual Antenna RTK GNSS Certus Evo contains a dual frequency RTK GNSS receiver that provides up to 1 cm accuracy positioning and supports all of the current and future satellite navigation systems, including GPS, GLONASS, GALILEO, BeiDou and QZSS. Dual antenna heading provides high accuracy heading that is not impacted by magnetic interference and has no motion requirements. Time Synchronization Certus Evo contains a GNSS disciplined oscillator that can act as the primary time source within a distributed time system, enabling access to ultra-accurate system time using PTP or NTP network time sync. Certus also has a high-accuracy 1PPS and frequency output. Multi Protocol Support Certus Evo features multiple interfaces including Ethernet, CAN, RS232, RS422 and GPIOs. Certus supports all the industry standard protocols including NMEA 0183, NMEA 2000, TSS, PASHR, Simrad as well as a wide variety of proprietary protocols. It features a rich web UI and 256GB of internal logging.

Low Size, Weight and Power (SWaP) at only 297g. Up to 100 TOPS GPU by NVIDIA® Jetson Orin™ NX Supports multiple camera and sensor interfaces 2x GbE and 2x USB3 for RGB/ Infrared/ hyperspectral cameras and lidar/ radar 2x GMSL2 for HDR/ 3D cameras Built-in UART and CAN to interact with flight controller 1x M.2 2230 for storage and 4G/5G communication ready Supports 4S-14S drone battery pack Compatible GMSL2 cameras with pre-built drivers

The QVM-200 is an ultra-compact video transmission module mounted on a small device that compresses camera video in real time and transmits it to a remote control device. This product features a built-in H.264/H.265 codec, compressing high-definition video at FHD (1920x180p) @ 60fps and UHD (3840x2160p) @ 30fps. It also supports various video transmission protocols, enabling real-time video control and operation. In particular, the QVM-200's built-in real-time high-compression video transmission technology enables ultra-low bandwidth video transmission, ensuring stable video transmission even in wireless environments with extremely limited bandwidth. It provides a MIPI camera interface and a USB port for connecting EO and IR cameras. Its minimal size and weight allow it to be installed even in ultra-compact drones with limited space, weight, and power consumption.

Orbit’s TT&C ground stations antenna must function flawlessly in order to provide a narrow beam width link in one-time single opportunity, flight test event. Add this factor to the turbulent weather that is often present at the ground station locations, and you are looking at a formidable hurdle. Orbit provides fixed, transportable, and portable antenna systems that feature auto-track, RSSI-track and GPS track tracking modes, unsurpassed tracking accuracy and durability to deliver the stable connection required for dependable data throughput. Our stabilized T&T antenna systems work in extreme temperature conditions (-40°C to 55°C) and in rough weather, for example, at base stations that are close to the ocean or on high mountain ranges.

For : Nose-Landing Gear Assembly Jig A350 Project 4.8m (L) x 2.5m (W) x 3m (H )