The KF-21 is the project which aims to replae the aged fighters in operation, F-4, and F-5 of the Republic of Korea Air Force and develop the indigenous Korean fighter aircraft which is equipped with performances suitable for the future battlefield of the country's air force. Korea's largest-scaled KF-21 project is the national R&D project with a development span of 10 years and 6 months and is driven with Indonesia under international joint development. Based on its development experience and infrastructure of a homegrown airplane, such as the KT-1 basic trainer, T-50 Advanced Jet Trainer, TA-50 Lead-in-Fighter-Trainer, and FA-50 Light Combat Aircraft, KAI is under development of the KF-21 project successfully. Through this project, KAI plans to develop the aerospace technology of Korea and contribute to national peace and security as well as economic development.

The AMT-206-1 composite tail rotor blade is a direct replacement for Bell 206A and 206B series helicopter tail rotor blades. Now fitted with a new style of feathering bearings manufactured by KAMATICS. These bearings provide a longer life expectancy, with a patented lining that provides lighter pedal loads and a higher level of chemical resistance, compared to that of the standard fabric Teflon-lined bearings. The AMT-206-1 tail rotor blade has a non-symmetrical airfoil section and incorporates a swept tip. The T/R Blade is primarily fabricated from uni-directional Graphite (carbon fiber) and Aramid (Kevlar™) continuous fibers suspended in an epoxy matrix and is fitted with a nickel abrasion strip on the leading edge. The abrasion strip is bonded on using a urethane adhesive. The AMT-206-1 composite tail rotor blades have a 30% cost advantage, twice the lifespan, higher strength and thrust, and a substantial noise reduction, making them safer and ideal for helicopter operators flying in noise-sensitive areas like national parks and built-up areas.

Counter-Drone System Planning & Optimization, Quantitative, Objective-Based Operational Performance Analysis & Management for Critical and Contested Areas

Silicon Carbide Products Used in Semiconductor Etching Processes

SAR Radar Antenna Assembly Module Telecommunication Radar Antenna Assembly Module

B Series incorporates the highly reliability Hypertac® hyperboloid contact which provides optimum performance in harsh conditions such as extreme mechanical shock and high mating cycles.

Ultra-High Accuracy MEMS Motus features some of the highest accuracy MEMS accelerometers and gyroscopes currently available. Motus’s inertial performance exceeds some FOG IMUs and is up to 100x smaller and 10x cheaper. Motus is put through Advanced Navigation’s intensive calibration process to provide consistently accurate data over an extended temperature range of -40°C to 85°C. Miniature Package Never before has such high inertial performance been available in such a small package. Motus consumes just over 1 cubic inch in volume and weighs only 26 grams. This makes it ideal for weight and size sensitive applications. Motus is available in an OEM package suitable for integration into larger products or an enclosed package for external and standalone use. Advanced Signal Processing Motus samples its sensors synchronously at 1000Hz through six individual 24-bit differential ADCs which minimizes noise as well as providing optimal thermal calibration and performance characteristics. 14 separate heavily filtered regulated power supplies ensure that each sensor and ADC is operating off the cleanest possible power supply. Reliability Motus has been designed from the ground up for mission critical control applications where reliability is very important. It is built on top of a safety oriented real time operating system and all software is designed and tested to safety standards with fault tolerance in mind. The hardware is designed and manufactured to mil standards. High Update Rate Motus outputs temperature calibrated sensor data at 1000Hz as well as filtered attitude at the same rate. This allows for control of dynamically unstable platforms.

Our products are used for manufacturing interior design components for civil and military aircraft construction. Sandwich structures are used in many areas of an aircraft (storage compartments, interiors, wings) to reduce weight. In order to structurally strengthen the honeycombs or insert them, they often have to be filled during the production process. Typical materials are one- and two-component epoxy resins with a very high proportion of hollow glass spheres. These require extremely gentle handling, as they would otherwise be destroyed, which in turn would result in an increase in density. Common application patterns are beads, circles, full surfaces and egde-filling. The job is often done manually, which results in long production times and high running costs due to material waste. Lack of reproducibility is just as problematic as the health hazard often posed by these media. The ViscoTec solution: Material is continuously fed to the dosing system by removal from a large container. With the help of a robot or axis system, suitable structures can be mapped reliably. A coordinated overall system delivers a dispensing result according to specification, in which operator interaction is reduced to a minimum.