This Control Actuation System (CAS) is a guidance system for unmanned flying objects. It consists of three MPS fin actuators that each independently position an aerodynamic fin. The maximum angle of incidence is ±8°, which allows the device to carry out highly precise dynamic manoeuvres. The miniature fin actuators that make up this Control Actuation System are manufactured by MPS Microsystems and were designed based on customer specifications. Designed to guide a very small object and disposing of an extremely limited space, these fin actuators meet strict requirements in terms of performance, weight - less than 100 g - and dimensions. To reduce the length of this actuator, MPS Microsystems used part of the screw length as the motor axis. This screw is equipped with a very compact 4-point contact bearing that simultaneously absorbs axial and radial loads. The angular play on the aileron axis is less than 0.1° rms. This actuator meets the storage and vibration requirements of military equipment.

With a peak torque of >200Nm / 1770 lbf-in and a rated torque of 80Nm / 708 lbf-in, the fully redundant DA 58-D is the strongest, electromechanical, fully integrated (actuator control electronics, position sensing, motor and drivetrain in one housing) actuator in the market. Besides the well-proven redundant RS 485 interface, the DA 58-D also features a redundant CAN bus interface. The DA 58-D has been developed for applications with the highest reliability demands. The redundant – two channel – design of the actuator allows continuous operation even if one of the two channels has failed. All major components such as the electric motors, control and communication electronics, and power supply are available twice (redundant). The actuator features a triple-redundant position sensor (2 out of 3 voting). Additionally there are several sensors integrated to provide diagnostic information such as current consumption, supply voltage levels and temperature readings. All major components of the actuator are continuously diagnosed by the microcontrollers of the actuator and its health status can be read via the redundant RS485 / CAN interface.

• Openable sleeves • Expandable sleeves • Convoluted conduits • Heat shrink tubing & sleeves • Heats shrink boots • Specific sleeves

EMCORE’s exclusive photonic integrated chip (PIC) technology delivers improved reliability and repeatability. The precision non-ITAR GEO-FOG 3D Dual features two GNSS antennas on a fixed PTK baseline to offer increased heading, pitch, and roll accuracy for static and dynamic applications where a single antenna system can be problematic. This dual antenna INS is the best choice for systems requiring heading at start-up or in low dynamic conditions. Highlights Data rate 10x faster than other available systems Cutting-edge sensor fusion for dependable, precise navigation in a full array of applications and conditions Six degrees of freedom (DoF) IMU with integrated gyros and accelerometers Technology Details Photonic Integrated Chip Technology EMCORE’s new photonic integrated chip (PIC) technology reimagines FOG technology by replacing individual fiber components with an innovative integrated planar optic chip. This results in a FOG with PIC Inside™ that’s even more reliable and delivers superior repeatability unit-to-unit. With three of these integrated photonic gyros at its core, the P-1750 IMU enables the GEO-FOG to provide the safe, accurate performance autonomous platforms demand. Learn More DSP Technology EMCORE’s DSP electronics improve FOG performance in critical areas such as scale factor and bias vs. temperature, scale factor linearity, and maximum input rate. EMCORE’s exclusive DSP design overcomes the limitations of analog signal processing, eliminating temperature-sensitive drift and rotation errors. GEO•FOG Manager The GEO•FOG Manager is ideal when integrating EMCORE’s GEO•FOG 3D and GEO•FOG 3D Dual INS. Learn More Developer’s Kit for Rapid Integration The KVH FOG/IMU Developer’s Kit includes easy-to-use software to accelerate your IMU and FOG integration, development, and interface efforts.

The RFcore Radar series are FMCW type radar and were developed to detect/track small air targets. The major difference between three models is detection performance. RX32B is fundamental model. RX128B have four times larger radar than RX32B. RX192A have six times larger radar then RX32B. The number of the product name means the number of antenna elements. All have compact and lightweight physical architecture that concentrates all the components required for radar, such as antenna, RF components and radar signal processor, in a small single housing. Transport can be carried in the carrier box and can be easily carried by one person. For installation, you can use a commercially available camera tripod. The weight is about 7.5kg (RX32B) and 15.9kg (RX128B), and the lower connection part is compatible with the tripod connection for the camera. Power supply requires 12VDC (RX32B) and 24VDC power (RX128B and RX192A). When using a battery, it is possible to connect a 12V battery or 24V battery to radars. Usage time may vary depending on the battery capacity. RFCORE recommended the constant power supply. Transfer of Status and BIT information and simple control of the RX32B, RX128B and RX192A are possible with a web browser using the Ethernet connection for authorized users. Using the terminal program provided with the radar, you can view the radar control and detected target information in real time. All RX Radar series’ Power Amp and Core Chip were designed using RFcore's own products.

The GSG-8 GNSS Simulator is an advanced software-powered turnkey simulator, supporting multi-constellation, multi-frequency, and hundreds of satellite signals. With an incredible 1000 Hz iteration rate, the GSG-8 GPS Simulator is ideal for space trajectories, custom PNT signals, hardware-in-the-loop, and any type of all-in-view satellites simulation. With the GSG-8 Simulator, you can generate RF signals to simulate how your receiver device will react in the real world, under the simulation parameters that you set. Control every aspect of your simulation, including 6 Degrees of Freedom (DoF) receiver trajectories, multi-vehicle simulation, multi-path signals, jamming and spoofing, as well as atmospheric interferences. The GSG-8 is the most popular positioning, navigation, and timing test solution offered through Safran’s GSG family of Skydel-based simulators. It was developed to deliver the highest standard of Global Navigation Satellite System (GNSS) signal testing and sensor simulation performance in an easy to use, upgradable and scalable platform.

1. Fixed Wing Aircraft MRO/Mod./Upgrades area 2. Starting with KAI’s military depot level maintenance program, 3. From providing service to KAI’s indigenous platform, Upon cooperation with global OEMs, KAEMS is capable of delivering various types of military solution with quality. [Military Business] - ROKN P-3CK Depot level maintenance - ROKAF E737 AEWCS Modification - F-16 US Airforce Depot level maintenance - KF-16 ROK Airforce Ram Coating Program - Training Jet T-50 FWD Fuselage Assemble

Saab's Electronic Warfare (EW) Countermeasure Dispensing Systems (CMDS) for airborne platforms provides self-protection in sophisticated, diverse and dense threat environments for your mission success and safe returns.