- Long life and precise movement control through fine-tuning - Shaft diameter 5mm~ - Accuracy G3~G7 - Shaft length differs depending on material, size, accuracy of shaft - Efficiency 85% or higher

The engine is suitable for MALE AUVs. Available in pusher and tractor configurations. Digital interface for control and monitoring. Stable operation at high altitudes and high temperatures. Ability to run at cold temperatures below -30°C without preheating.

STERNA System accurately finds True North in virtually all terrains and regardless of the weather conditions. The performance of STERNA System is not disturbed by gear carried by its operator or if used next to heavy armored vehicles. It remains highly accurate even when deployed on reinforced concrete floors or in dense urban settings. STERNA System operates reliably even in GPS denied environments and does not require the operator to carry any support resources to determine True North. If your mission success depends on the highest level of accuracy and precision, there is no substitute for STERNA System.

The sky’s the limit with the Bell 505. A high-tech flight deck and adaptable cabin design make it an extremely cost-competitive, and capable for any challenge.

Continental connectors are manufactured with highest quality materials. Our contacts are machined to close tolerances as opposed to stamped and formed styles. All molding compounds are glass reinforced, flame retardant and able to withstand severe environmental and mechanical requirements. Military connector families conform to the highest Defense Supply center (DSCC) standards, which require qualification testing and continued periodic requalification under the surveillance of government representatives to maintain our Company Qualified Product Listing (QPL)

The RFcore Radar series are FMCW type radar and were developed to detect/track small air targets. The major difference between three models is detection performance. RX32B is fundamental model. RX128B have four times larger radar than RX32B. RX192A have six times larger radar then RX32B. The number of the product name means the number of antenna elements. All have compact and lightweight physical architecture that concentrates all the components required for radar, such as antenna, RF components and radar signal processor, in a small single housing. Transport can be carried in the carrier box and can be easily carried by one person. For installation, you can use a commercially available camera tripod. The weight is about 7.5kg (RX32B) and 15.9kg (RX128B), and the lower connection part is compatible with the tripod connection for the camera. Power supply requires 12VDC (RX32B) and 24VDC power (RX128B and RX192A). When using a battery, it is possible to connect a 12V battery or 24V battery to radars. Usage time may vary depending on the battery capacity. RFCORE recommended the constant power supply. Transfer of Status and BIT information and simple control of the RX32B, RX128B and RX192A are possible with a web browser using the Ethernet connection for authorized users. Using the terminal program provided with the radar, you can view the radar control and detected target information in real time. All RX Radar series’ Power Amp and Core Chip were designed using RFcore's own products.

THE FUTURE OF FIGHTER JETS

With a 99% win-rate in simulated F-16 dogfights versus active-duty Air Force and Navy fighter pilots, Hivemind is learning to execute a variety of missions from Beyond Visual Range strike to suppression of enemy air defense. The future of air dominance will be powered and flown by Hivemind.

It Starts With The F-16

Hivemind will deploy as a digital co-pilot on a U.S. Air Force F-16, with the goal of rapidly scaling across next-generation aircraft, F-22s, F-18s, and other fighter jets. Hivemind will make legacy fighters relevant for decades to come and will power the next generation of military aircraft.

We carry a wide range of aerospace-grade materials in round bar and sheet, including: -Alloy 718 (AMS5596) -Alloy 625 (AMS5599) -Alloy X (AMS5536) There is no minimum order quantity ? we can cut from a single piece and ship within 1?2 days, complete with full material traceability. For non-stock grades, shapes, and standards, we can source materials from suppliers worldwide with a lead time of approximately 2 weeks, also with no minimum order quantity.