High impedance D-Sub connectors are designed to ground the outer shield of a twinax or quadrax contact directly to the shell of the connector. A multi-finger ground spring fixed around the shell provides a multi-point contact engagement that affords superior EMI shielding. The end result is an extremely low contact resistance when measured from the contact outer body to the connector flange, ensuring minimal RF noise and high durability of over 500 mating cycles.

옥외 스펙트럼 모니터링 및 위치 탐지 솔루션 R&S®UMS400 범용 모니터링 시스템은 8kHz에서 8GHz까지 스펙트럼 모니터링 및 방향 탐지를 지원합니다. 또한, R&S®CS-MC20 마이크로파 컨버터를 통해 최대 20GHz까지 확장할 수 있습니다. 무선 통신 서비스의 주파수 범위가 점점 증가함에 따라 최대 8GHz, 경우에 따라 최대 20GHz까지 모니터링 스테이션이 필요합니다. 일반적으로 가장 높은 감도를 위해 케이블 손실을 최소화하기 위해 안테나 근처에 모니터링 센서를 설치해야 합니다. R&S®UMS400과 R&S®CS-MC20 모두 옥외 하우징 옵션을 통한 야외 설치가 가능합니다.

Our military aerospace AGSE solutions are important to the militaries that use them to maintain and service their aircraft. The aircraft servicing and maintenance hardware and armament handling equipment we develop, distribute, and support are relied on for mission success worldwide.

SKYLIGHT™ is a mono or bi-constellations dual civil/military GNSS receiver, providing the highest navigation performances and operational flexibility. It is suitable for a large range of applications: aircrafts, helicopters, UAVs, missiles, land vehicle.

Official Korean Distributor and Licensee of Parker Velcon, offering industrial filter systems and filter cartridges Filter vessels and elements (cartridges): Filter/separator vessel and cartridge, Moisture-absorbing Aquacon filter vessels and cartridges; Micronic filter vessels and cartridges (0.5 Micron to 25 micron), Natural Gas filter vessels and cartridges; etc.

The fully redundant DA 30-HT-D has been developed for applications with the highest reliability demands. The redundant – two channel – design of the actuator allows continuous operation even if one of the two channels has failed. All major components such as the electric motors, control and communication electronics, and power supply are available twice (redundant). The position sensor features a three channel design (for 2 out of 3 voting). Additionally, there are several sensors integrated to provide diagnostic information such as current consumption, supply voltage levels and temperature readings. All major components of the actuator are continuously diagnosed by the microcontrollers of the actuator and its health status can be read via the redundant RS485.

i3system’s line scanning X-ray detector platform, XID-C15DP/XID-C24DC, is a high performance and cost effective solution for dental panoramic, cephalometric applications. i3system’s direct type sensor ensures the most sharp images among the current products in the market. XID series is designed for compact size and easy installation. High DQE(Direct Quant㎛ Efficiency) enables high performance at lower dose of X-ray. Introduction Indirect type X-ray detector uses the scintillator and the photo-diode(CCD or CMOS sensor) for conversion of the X-ray into the light and for taking images espectively. But the light scatters and goes extinct during it passes through the scintillator and reaches to the CCD or CMOS sensor. As a result, it is inevitable to get blurred image. In the mean time, XID C15DP, direct type detector, converts X-rays into electronic signals directly without conversion process of light. Because X-ray is not converted into light, it provides much sharper images than indirect type detector. XID C15DP is designed to compact for easy installation. It provides Gigabit Ethernet port on the detector for easy configuration. Instead of Gigabit Ethernet, camera link or optical interface can be provided according to requirements of users.

Monitors abnormal engine operation based on digital and analog signals from the aircraft engine. It calculates engine life indices and detects engine malfunctions for generate a Pilot Fault List (PFL), which will stored in memory. When an engine failure is detected, it provides warning for display on the Central Maintenance Panel (CMP). Developed as a replacement for obsolete, achieving 60% cost competitiveness compared to equivalent products. - x1 MIL-STD-1553B - x16 Discrete Inout - x14 Discrete Output - x3 Analog Input - x1 RS-232 - Size: 283 x 265 x 89 (mm) - Weight : 4.1Kg - Environment : MIL-STD-810G - EMI/EMC : MIL-STD-461G - Power : MIL-STD-704F (28VDC, 25W)