WPGM0206012M is a 12W Gallium Nitride (GaN) Monolithic Microwave Integrated Circuit (MMIC). WPGM0206012M is useful for various application as it is covering from 0.5GHz to 8.5GHz. Spec : Frequency : 0.5-8.5GHz Saturated Output Power : 19.5W@4GHz PAE : 22.49% Power Gain : 5.91dB@4GHz Operating Voltage : 48-50V Please contact WAVEPIA for more information.

SCD’s advanced 12μm VOx Microbolometer stands out as the ideal choice for VGA LWIR systems. With its exceptional image quality, remarkably low Noise Equivalent Temperature Difference (NETD), very low time thermal constant (Tau), rapid image acquisition, and minimal weight, SCD’s Microbolometer ranks among the leading LWIR sensors in the market. It is suitable for a wide range of applications, specifically tailored to meet challenges associated with Size, Weight, Power (SWaP) constraints and highly dynamic applications. This product continues SCD’s long heritage uncooled detectors technology, along with our 25μm and 17μm pitch families, fielded and combat proven for more than 20 years.

i3system’s line scanning X-ray detector platform, XID-C15DP/XID-C24DC, is a high performance and cost effective solution for dental panoramic, cephalometric applications. i3system’s direct type sensor ensures the most sharp images among the current products in the market. XID series is designed for compact size and easy installation. High DQE(Direct Quant㎛ Efficiency) enables high performance at lower dose of X-ray. Introduction Indirect type X-ray detector uses the scintillator and the photo-diode(CCD or CMOS sensor) for conversion of the X-ray into the light and for taking images espectively. But the light scatters and goes extinct during it passes through the scintillator and reaches to the CCD or CMOS sensor. As a result, it is inevitable to get blurred image. In the mean time, XID C15DP, direct type detector, converts X-rays into electronic signals directly without conversion process of light. Because X-ray is not converted into light, it provides much sharper images than indirect type detector. XID C15DP is designed to compact for easy installation. It provides Gigabit Ethernet port on the detector for easy configuration. Instead of Gigabit Ethernet, camera link or optical interface can be provided according to requirements of users.

Consists of a Data Transmission and Recording Unit (DTRU) for data transmission and collection, and a Removable Mass Memory (RMM) for data storage. Stores pre-planned flight mission data in the RMM on the ground and transmits it to the aircraft via the DTRU. Collects various mission data (flight data, monitoring data, video data, and audio data) during flight, stores it in the RMM, and transmits it to the ground for mission analysis. - x5 ARINC-818 Recording as H.264 - x2 Analog audio recording - x7 MIL-STD-1553B Bus Monitoring - x2 Gigabit Ethernet Monitoring - 512GB Solid-State Disk (up to 2TB) - Size : 160.1x146.0x232.4 mm - Weight : 4.25Kg - Power : MIL-STD-704F (28VDC, 58W) - Environment: MIL-STD-810G - EMI/EMC: MIL-STD-461G

The Series 23 SuperNine® advanced performance MIL-DTL-38999 connector series provides many of the technology advances exceeding MIL-DTL-38999 Series III. Higher mating cycles, integrated banding porch, PC Tail and standoff availability and crimp termination Hermetics are all part of the family.

Our radars’ low-Size, Weight, and Power (SWaP) means ample room for other onboard sensors, such as Electro-Optical and Infrared (EO/IR) cameras. Users no longer need to decide which sensor to include and which to exclude. Instead, they can understand the bigger picture. Highly reliable, the NSP-3 has a recommended maintenance interval of 1,250 hours. It can gather data over land and maritime environments and can be used for applications as broad as sea ice monitoring and search and rescue, as well as specialized intelligence, surveillance, and reconnaissance (ISR) missions.

Winchester Interconnect Micro, formerly known as Ulti-Mate Connector, designs and manufactures a broad range of precision engineered Micro D Connectors that are designed to be environmentally sealed, making them suitable for a wide range of applications. They can operate in temperatures ranging from -55°C to 125°C, with high-temperature versions available for more extreme environments (indicated by "HT" in the product name). These connectors come with 9 to 100 contacts and adhere to the MIL-DTL-83513 standard. And, leading manufacturer for high density, lightweight Nano connectors available in 9 to 51 contacts, these connectors cater to various applications. As a QPL qualified supplier for MIL-DTL-32139 product.