[Cutting by water jet] Micro water jet cutting: The micro water jet enables a refined process to be carried out in precision cutting. This high-precision technology reduces the jet diameter by a factor of 5 and makes water jet cutting more precise by a factor of 10. The micro water jet achieves a cutting accuracy of +/- 0.01 mm and a positioning accuracy of ±0.005 mm. The proven advantages of the cold cutting process remain unchanged. In the pure water process, the cutting width was reduced to 0.2 mm in the abrasive process for hard materials such as nickel-based alloys and titanium. The new technology controls the cutting process and manipulates the cutting path depending on the contour and speed enabling a highly precise cut. Standard waterjet cutting: Water jet cutting is highly efficient and at the same time less severe than other cutting techniques. Low process forces and thermal loads prevent bending or melting. We can cut filigree delicate contours from practically all nickel alloys and titanium alloys. Using our standard process we can cut a range of shapes and dimensions according to customer requirements and drawings and achieve tolerances of +/- 0.1 mm or +/- 0.2 mm.

We have taken the standard housing configuration of the P1 & P3 mounting dimensions while incorporating true differential pair contacts within the P1 & P3 dimensional constraints. P1 connector housing contains 21 position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P1 type housing.

Processor - NXP Quad Core PowerPC QorIQT2080 up to 1.8GHz - 6 DMIPS/MHz per core (up to 43,200 DMIPS@1.8GHz) - 128b AltiVecSIMD unit (up to 72 GFLOPs@1.8GHz) Memory - 4GB soldered 64-bit DDR3L SDRAM with ECC - 256MB 16-bit NOR flash - 64GB SATA NAND SSD - 512KB NvRAM Form Factor - 3U OpenVPX - Conduction-Cooled

ELECTROMECHANICAL RELAYS

Type : Axial (3P) Size(Ø, mm) : 310 × 109 Weight(kg) : 37 N. Speed(rpm) : 2100 N. Torque(Nm) : 450 N. Power(kW) : 100

CATIS™ is an ultra-high-resolution, small satellite imaging radar device independently developed by Lumir. It consists of three components: the radar signal transmission/reception device SCEU, an active phased array antenna SATA, and a data downlink antenna KaPA. This X-band imaging radar device is designed for small satellites weighing 150 kg, offering an ultra-high resolution of 0.3 m. It transmits wideband RF signals to the observation area while orbiting at an altitude of 500 km and receives the reflected signals to acquire Earth observation data.

DS Aether CT provides various industrial Gas Tube Trailers such as Helium (He), Hydrogen (H2), Neon (Ne), Nitrogen (N2) and Argon (Ar), as well as CNG. The working pressure is set to national requirements or customer's demands such as 166 bar, 200 bar, or 250 bar. The color of the jumbo tubes and skid frames follows ISO color codes, or the designations of customers.

This system product is a product that directly supplies and heats lubricant oil for smooth operation of the main engine cylinder’s metallic and mechanical movement. Lubricator, a product that supplies lubrication directly to the main engine cylinder liner, can control injection timing and consumption using an electronic control method that responds to the movement of the main engine piston. The alpha lubricator system is based on an algorithm controlling the cylinder oil dosage proportionally to the sulphur content in the fuel and, fuel consumption on particular load of engine. Minimum cylinder oil dosage is required to provide an adequate oil film and detergency properties. Everllence and WIN GD engines are currently applying the second generation Lubricator type, the Everllence type is Mk-I and the WIN GD type is Mk-ε (Epsilon).