Discover why GE's Passport engine is B-52 ready.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Monitors abnormal engine operation based on digital and analog signals from the aircraft engine. It calculates engine life indices and detects engine malfunctions for generate a Pilot Fault List (PFL), which will stored in memory. When an engine failure is detected, it provides warning for display on the Central Maintenance Panel (CMP). Developed as a replacement for obsolete, achieving 60% cost competitiveness compared to equivalent products. - x1 MIL-STD-1553B - x16 Discrete Inout - x14 Discrete Output - x3 Analog Input - x1 RS-232 - Size: 283 x 265 x 89 (mm) - Weight : 4.1Kg - Environment : MIL-STD-810G - EMI/EMC : MIL-STD-461G - Power : MIL-STD-704F (28VDC, 25W)

SAF-FIRES™ is a standards-based, image generator agnostic, and scalable Call-For-Fire and Close Air Support training simulation with autonomous Smart Trainer suitable for deployment in Joint Fires and accreditable JTAC training simulators. Built upon the same Call-For-Fire and Close Air Support software engine that powers the accredited simulation Fires FST™, SAF-FIRESTM delivers the same mature and complete Joint Fires training solution but makes it available for integration with any DIS, HLA or CIGI compatible simulation or Image Generator. Supporting both conventional near-peer and counter-insurgency operational scenarios, SAF-FIRES™ enables JFOs and JTACs to train realistically in a modern complex battlespace against an agile and adaptive adversary. Heightened realism and cognitively challenging training are enabled through the incorporation of non-combatants, urban clutter, UAV surveillance, various close air support platforms and accurate military targeting procedures.

High impedance D-Sub connectors are designed to ground the outer shield of a twinax or quadrax contact directly to the shell of the connector. A multi-finger ground spring fixed around the shell provides a multi-point contact engagement that affords superior EMI shielding. The end result is an extremely low contact resistance when measured from the contact outer body to the connector flange, ensuring minimal RF noise and high durability of over 500 mating cycles.

The all-new AV3 Assault Rotary Wing Helmet, releasing in 2026! Engineered with precision for extreme conditions, this helmet is a game-changer for aviators and adventurers alike. Some key features of this helmet include the maxillofacial shield, visor shroud system, koroyd impact liner, fit knob system and NVG compatibility.

Explore nanoscale structure with clarity, speed, and confidence. Tescan’s STEM solutions are purpose-built for advanced materials research, semiconductor analysis, and detailed nanoscale characterization. With integrated 4D-STEM, precession-assisted diffraction, and synchronized EDS workflows, our instruments deliver actionable insight with unmatched usability—whether you're mapping strain, analyzing phases, or accelerating failure analysis and R&D.

The SWE550S is a rugged 6U VPX fully managed Layer-2/3 Ethernet switch aligned with the SOSA profile, providing blazing-fast 25/100 GbE switching via a 3.2 Tbps fabric and flexible I/O reconfiguration. • 3.2 Tbps switch fabric delivering full wire-speed bandwidth (~2.5× typical) • Front: up to 2×100 GBASE-SR4 (MPO); Rear: up to 7×100 GBASE-SR4, SWE540A-compatible I/O • Fat-pipe ports reconfigurable into thin-pipe ports; copper ports support 25/100→10/40 Gb speed downgrade • Dual-core ARM + OpenWare™ management; built-in storage sanitization • SOSA-aligned 6U VPX form factor; air & conduction cooled; rugged Levels 1, C, E