Hydraulic top bracing is an attenuation device installed between the main engine and the hull of the ship to reduce thermal expansion and vibration from the main engine to natural frequencies. The operating principle is an automatic control operating system through in/out and on/off the operating range of the hydraulic top bracing according to the rpm of the main engine. The number of hydraulic cylinders per engine is typically 2, 4, 6 depending on the type of engine, up to 8 are installed if necessary, and 1~2 of control panels are installed.

Duratek's power supplies and power distribution units are designed and manufactured to generate and distribute stable electrical power required by equipment, tailored for defense applications in naval, ground, aerospace, and space environments.

The CAS-500(Compact Advanced Satellite), phase #1 project is the project in which KAI aims to develop a CAS500-1 by operating a joint design team with Korea Aerospace Research Institute(KARI) and to transfer the government’s satellite development technology to the industries. Then, KAI initiates the development of the CAS500-2 project and establish the industry-led development as well as mass-production infrastructure.

ORSKOREA’s cylindrical grinding machines are engineered to deliver superior surface quality and tight tolerances for high-value parts. They are widely used in aerospace, defense, automotive, medical, and electronics industries for components that demand both strength and precision—such as engine shafts, landing gear parts, gears, and bearings. Key Advantages • Handles diverse, small-batch productions with consistent repeatability • Exceptional dimensional precision for tight-tolerance parts • Supports tapered and curved surface grinding • Flexible workpiece capacity with swing up to 350 mm • Smooth table movement with low noise and vibration for stable operation By combining precision, versatility, and long-term reliability, ORSKOREA’s cylindrical grinders provide manufacturers with the performance needed to meet mission-critical requirements.

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

R HUGHES' Ca-Zoom PTZ 140 is a Pan-Tilt Zoom Camera inspection equipment equipped with the Ca-Zoom® 6.2 system. This equipment is capable of a total of 432x zoom with 36x optical zoom and 12x digital zoom, increasing inspection efficiency. In addition, two high-performance 35W lights are installed in the light source to enable more smooth inspection. The inspection technology of the PTZ Camera Ca-Zoom® line of products makes them ideal for inspecting large areas that are difficult for humans to access, such as tanks, vessels, pipelines or nuclear power plants.

Technology research that needs to be developed/secured to efficiently train future combat pilots ETS must have the ability to provide a realistic training environment in which pilots can immerse themselves in training through the use of simulations and CGFs within a real platform. The advantage of ETS is that it provides trainees with a training experience that is close to the real thing and reduces overall system operating costs by replacing real systems and consumables with simulations. Developed countries are already continuing to attempt to apply various core technologies to increase the efficiency of ETS. Hangil C&C Co., Ltd. is the only ETS development company in Korea, and is striving to develop cutting-edge ETS by combining years of research and development experience and its core technologies.

Main Characteristics Excellent broadband characteristics Radiation patterns virtually independent of frequency Only one antenna required to cover a wide frequency range Selectable polarization plane Sturdy construction Suitable for mobile use Main Use Optimized for radiomonitoring and measurements Design Owing to its broadband characteristics and the virtually frequency-independent radiation patterns, the SLP – 200M-001G covers a very wide frequency range The sturdy construction makes the antenna Suitable for stationary and mobile applications