With a peak torque of >200Nm / 1770 lbf-in and a rated torque of 80Nm / 708 lbf-in, the fully redundant DA 58-D is the strongest, electromechanical, fully integrated (actuator control electronics, position sensing, motor and drivetrain in one housing) actuator in the market. Besides the well-proven redundant RS 485 interface, the DA 58-D also features a redundant CAN bus interface. The DA 58-D has been developed for applications with the highest reliability demands. The redundant – two channel – design of the actuator allows continuous operation even if one of the two channels has failed. All major components such as the electric motors, control and communication electronics, and power supply are available twice (redundant). The actuator features a triple-redundant position sensor (2 out of 3 voting). Additionally there are several sensors integrated to provide diagnostic information such as current consumption, supply voltage levels and temperature readings. All major components of the actuator are continuously diagnosed by the microcontrollers of the actuator and its health status can be read via the redundant RS485 / CAN interface.

Learn more about Tronair's technical manuals, troubleshooting, maintenance schedules, and products - plus our 3 authorized service centers located in Europe, 2 in Asia and 1 in North America allow our customers close and convenient locations to have any Tronair equipment repaired and tested.

D-100 MIL 1&2 operating Instructions.

CAPHMICRO has the ability to design and manufacture wire harnesses and cable assemblies for defense, aerospace, and space launch vehicles/satellites. We design and manufacture in compliance with IPC-620 and J-STD-001 standards. Additionally, we have a global supply chain capable of quickly supplying a wide range of materials. We provide comprehensive solutions for wire harnesses, from design through to manufacturing and inspection.

Whether satellites, spacecraft or space debris – GESTRA, the "German Experimental Surveillance and Tracking Radar", is a state-of-the-art radar system for observing and tracking objects in space. It operates in the microwave range and explores the Low Earth Orbit of 300 to 3,000 kilometres, i.e. the range in which most satellites and the International Space Station (ISS) are located. This makes it possible, for example, to protect space systems or the ISS from a collision with debris particles by providing a timely warning. Millions of tiny particles orbit the earth and, at a speed of around 28,000 km/h, pose a threat to active space technologies. GESTRA was developed and built by the Fraunhofer Institute for High Frequency Physics and Radar Techniques FHR on behalf of the German Space Agency at DLR.

EMCORE’s exclusive photonic integrated chip (PIC) technology delivers improved reliability and repeatability. The precision non-ITAR GEO-FOG 3D Dual features two GNSS antennas on a fixed PTK baseline to offer increased heading, pitch, and roll accuracy for static and dynamic applications where a single antenna system can be problematic. This dual antenna INS is the best choice for systems requiring heading at start-up or in low dynamic conditions. Highlights Data rate 10x faster than other available systems Cutting-edge sensor fusion for dependable, precise navigation in a full array of applications and conditions Six degrees of freedom (DoF) IMU with integrated gyros and accelerometers Technology Details Photonic Integrated Chip Technology EMCORE’s new photonic integrated chip (PIC) technology reimagines FOG technology by replacing individual fiber components with an innovative integrated planar optic chip. This results in a FOG with PIC Inside™ that’s even more reliable and delivers superior repeatability unit-to-unit. With three of these integrated photonic gyros at its core, the P-1750 IMU enables the GEO-FOG to provide the safe, accurate performance autonomous platforms demand. Learn More DSP Technology EMCORE’s DSP electronics improve FOG performance in critical areas such as scale factor and bias vs. temperature, scale factor linearity, and maximum input rate. EMCORE’s exclusive DSP design overcomes the limitations of analog signal processing, eliminating temperature-sensitive drift and rotation errors. GEO•FOG Manager The GEO•FOG Manager is ideal when integrating EMCORE’s GEO•FOG 3D and GEO•FOG 3D Dual INS. Learn More Developer’s Kit for Rapid Integration The KVH FOG/IMU Developer’s Kit includes easy-to-use software to accelerate your IMU and FOG integration, development, and interface efforts.

Current list of Lockheed Martin products.

Connectors