ALTERNATIVE TO M19648/1 SERIES

The new Super-TAC IMU integrates three fiber optic gyros that exceed tactical grade performance with three high-accuracy Micro-Electro-Mechanical Systems (MEMS) accelerometers and state-of-the-art support electronics in a single small, lightweight package. This solution addresses the need for superior inertial performance in a tactical- grade package, critical for operation in GPS denied and contested environments. The Super-TAC IMU measures change in velocity and angle, utilizing a configurable variable synchronous data link control (SDLC) digital serial bus. The Super-TAC is configured to offer customers the best value solution when designing new systems as well as provide the flexibility to upgrade existing platforms. The Super-TAC IMU employs state-of-the-art optics with fewer components, providing significant performance and reliability improvements across standard military environments. Background Emcore, located in Budd Lake, NJ has been designing, developing and producing inertial components, sensors and navigation systems for Space, Ground, and Avionic applications for over 35 years. Emcore has been developing Fiber Optic Gyros (FOGs) since the early 1990s, producing and delivering IMU products with performance ranging from tactical to strategic grade PERFORMANCE GYRO PERFORMANCE Bias Stability < 0.05 °/hr. (1σ) Angle Random Walk ( ARW) ≤ 0.01 °/√hr. (1σ) Scale Factor Repeatability ≤ 100 ppm (1σ) Scale Factor Linearity ≤ 50 ppm (1σ) Angular Rate Range 1,000 °/sec Acceleration Range 100,000 °/sec2 ACCELEROMETER PERFORMANCE Range ± 25 g Bias Variation ≤ 50 μg (1σ) Scale Factor Stability ≤ 300 ppm (1σ) SYSTEM PERFORMANCE Bandwidth (adjustable) 800 Hz (gyros) 150 Hz (accelerometers) MTBF >25,000 hr.

- Long life and precise movement control through fine-tuning - Shaft diameter 5mm~ - Accuracy G3~G7 - Shaft length differs depending on material, size, accuracy of shaft - Efficiency 85% or higher

We has built a global partnership with accumulated technology to produce/supply major structures to Boeing and Airbus. By manufacturing large-scale composites that make the fuselarge of an aircraft, automated production technology applying robot concepts, non-destructive inspection technology and flow production line, etc. we are competing with advanced aircraft manufacturers with the best technology, quality and productivity by developing advanced technologies and equipment.

INCONEL® Alloy 230 Bars-Sheets and Plates INCONEL® Alloy 600 Bars-Sheets and Plates-Wire-Tubes and Pipes INCONEL® Alloy 601 Bars-Sheets and Plates-Wire-Tubes and Pipes INCONEL® Alloy 617 Bars-Sheets and Plates INCONEL® Alloy 625 Bars-Sheets and Plates-Tubes and Pipes INCONEL® Alloy 718 Bars-Sheets and Plates INCONEL® Alloy X-750 Bars-Sheets and Plates INCONEL® Alloy HX Bars-Sheets and Plates-Tubes and Pipes NIMONIC® Alloy 75 Bars-Sheets and Plates NIMONIC® Alloy 80A Bars-Sheets and Plates NIMONIC® Alloy 90 Bars-Sheets and Plates-Wire-Strip NIMONIC® Alloy 263 Sheets and Plates UDIMET® Alloy 188 Bars-Sheets and Plate UDIMET® Alloy L-605 Bars-Sheets and Plates Waspaloy® Sheets and Plates

CATIS™ is an ultra-high-resolution, small satellite imaging radar device independently developed by Lumir. It consists of three components: the radar signal transmission/reception device SCEU, an active phased array antenna SATA, and a data downlink antenna KaPA. This X-band imaging radar device is designed for small satellites weighing 150 kg, offering an ultra-high resolution of 0.3 m. It transmits wideband RF signals to the observation area while orbiting at an altitude of 500 km and receives the reflected signals to acquire Earth observation data.

Poongsan has been producing a variety of copper and copper alloy plates, ranging from copper products for everyday life to high-tech industrial materials. These copper and copper alloy plates, which are recognized as high-quality materials at home and abroad, are representative industrial basic materials that are widely used in all industrial fields, including automobiles, electrical and electronics, semiconductors, communications, construction, and machinery. Poongsan has various casting facilities, including the world's largest shaft furnace, a hot mill capable of continuously rolling 6-ton slabs, a tandem mill, and a 20-stage cold rolling mill, as well as various hot and cold rolling facilities and heat treatment furnaces. We are building a large-scale integrated production system from the casting process to finishing processes such as cutting and packaging. Poongsan's rolled products are produced in various sizes depending on the type, ranging from 630mm in width, 0.03mm in thickness, and thickness tolerance to 2/1000mm. These products have accurate specifications and physical properties and a smooth surface thanks to the establishment of a thorough quality control system using cutting-edge inspection equipment. Excellent. Poongsan's copper and copper alloy rolled products are produced in a variety of ways, including pure copper, brass, phosphor bronze, nickel silver, cupronickel, and special alloy (PMC26 and other) depending on the alloy composition and casting method. In particular, in response to market demands for new high-strength copper alloys due to technological advancements such as the Internet of Things and electric vehicles, we have developed new alloys (P1000HS and others) and are applying them to high-tech products requested by customers.