항공 엔진용 테스트셀·시험장비 및 데이터 솔루션을 설계·구축하는 세계적 기업으로, 상업·국방·MRO 고객의 터보팬/터보샤프트/APU 등 다양한 엔진 시험 요구를 지원합니다.

GAIN CRITICAL CLARITY WITH SATELLITE TASKING Task ICEYE SAR satellites to access groundbreaking data on any location on Earth – day or night and in any weather. The process is simple and images are usually delivered within 24 to 48 hours of your initial request. ORDERING SAR DATA – MADE SIMPLE We believe access to reliable and timely SAR Earth observation data should be available to all, so we provide access options designed to meet your specific mission needs and collection timeframes. The process begins with defining your area of interest, revisit frequency and other parameters. The first images are usually acquired, downlinked, decoded and processed within 24 hours of the initial request and delivered within 8 hours after that.

Supported by a rugged internal combustion engine compatible with heavy fuels, Reliant delivers over 10 hours of persistent ISR without runways, launchers, or recovery gear. Designed for high-wind, high-altitude, and denied environments, Reliant excels where legacy platforms fall short. Dual swappable payload bays support ISR, SIGINT, or EW missions, while onboard edge AI processing enabled by NVIDIA Jetson Orin NX modules delivers real-time threat detection and adaptive rerouting, even without connectivity. The platform can be deployed by a two-person team in under 10 minutes using a compact 10×10-meter footprint for launch and recovery from rooftops, vehicles, ships, or remote terrain. With an IP55-rated, all-weather design and reliable GNSS-denied navigation, Reliant gives operators the flexibility and resilience required to operate in complex, contested battlespaces.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Engine Start Begins with ATS. The Air Turbine Starter (ATS) is a key component of an aircraft's secondary power system, driven by Bleed Air supplied from the Auxiliary Power Unit (APU) to accelerate the engine up to approximately 8,900 RPM, enabling engine start. Through the in-house development and localization of the ATS, we have incorporated power generation, optimal design of the shear section with consideration of failure, Containment functionality, as well as lubrication and power transmission systems. In addition, we have secured manufacturing and assembly technologies and continue development aimed at successful operation and the establishment of a mass production system.

옥외 스펙트럼 모니터링 및 위치 탐지 솔루션 R&S®UMS400 범용 모니터링 시스템은 8kHz에서 8GHz까지 스펙트럼 모니터링 및 방향 탐지를 지원합니다. 또한, R&S®CS-MC20 마이크로파 컨버터를 통해 최대 20GHz까지 확장할 수 있습니다. 무선 통신 서비스의 주파수 범위가 점점 증가함에 따라 최대 8GHz, 경우에 따라 최대 20GHz까지 모니터링 스테이션이 필요합니다. 일반적으로 가장 높은 감도를 위해 케이블 손실을 최소화하기 위해 안테나 근처에 모니터링 센서를 설치해야 합니다. R&S®UMS400과 R&S®CS-MC20 모두 옥외 하우징 옵션을 통한 야외 설치가 가능합니다.

Primarily used in medium-sized and large satellites, it provides high torque performance and momentum conservation. By localizing the Control Moment Gyro controller, which had previously been imported for Korea’s domestic satellite industry, Lumir has gained a competitive advantage in both performance and cost.

CI Systems사의 는 I-레벨 광학 테스트 및 실험실 테스트를 수행하는 데 이상적인 장비입니다. 소형이기 때문에 휴대 가능하며, 컴퓨터화되어있어 차량에 설치할 수 있습니다. 열화상 장비 및 가시광 센서에 대한 종합적인 테스트를 현장에서 할 수 있어 D-레벨 시설 없이도 테스트를 효율적으로 수행할 수 있습니다. 콜리메이터, 방사선원(블랙바디, 가시광 광원), 타깃 휠(수동 또는 전동)로 구성되며, CI Systems의 CTE 소프트웨어와 연동 시 간편하고 객관적이며 반복성을 극대화한 테스트가 가능합니다. 환경 변화에도 높은 정확도를 유지하며, 환경 챔버 테스트, 생산 라인 테스트, 현장 테스트 등 다양한 환경에서 활용할 수 있습니다. The CI Systems ILET (Intermediate-Level Electro-Optical Tester) family of test systems is ideally suited for performing I-level optical tests and laboratory testing. Portable, compact and computerized, ILET testers can be installed on a vehicle, bringing comprehensive testing of thermal imagers and visible light sensors to the field, reducing the need of D-Level facilities. The basic ILET configuration includes a collimator, a radiation source (blackbody and/or visible light source) and a target wheel (manual or motorized). The ILET is easy to use when interfaced with CI Systems’ CTE software (optional), minimizing testing turnaround time and maximizing testing objectivity and repeatability. The testers retain their accuracy over a wide range of ambient temperatures. Thanks to the ILET’s outstanding features and versatility, it is useful in a variety of applications such as testing in environmental chambers, testing on production lines and testing in the field..