The Global 5500 aircraft is a part of Bombardier’s renowned long-range, large-cabin Global aircraft family. It has ample power and endurance, proven reliability and advantageous maintenance intervals. Its large cabin provides plenty of space for workstations, patient transport and mission equipment.

It is especially suited for demanding applications, which require reliable performance, such as missile seeker gimbal stabilization, where small size and low power consumption is required, while in a low cost design that is also ideally suited for high volume commercial applications. System Performance PARAMETERS SPECIFICATIONS Standard Ranges ±100°/sec, ±200°/sec, ±400°/sec Input Voltage + and - 5.0 Vdc Bandwidth 110 Hz Output Noise < 005°/sec/√Hz Scale Factor Accuracy ±1% Nominal Features Dual Axis Capabilities in Small Form Factor Miniature Size: Only 25gm.(1.05” x 0.71” diameter) Hermetically Sealed In Stainless Steel Cylinder High Reliability DC Input/High-Level DC Analog Output Low Cost Applications Tank Turret Stabilization Missile Targeting Platform Stabilization Antenna Stabilization Camera Stabilization Spacecraft

The S10s, the first model of the PabloM series, is a loitering munition designed for strike missions. Leveraging mesh communication and AI-enabled swarm flight, it can execute both simultaneous and sequential self-destructive strikes against targets, effectively neutralizing diverse “anti-drone” systems. The S10s launches autonomously from a dedicated platform and can sustain flight for over 30 minutes, enabling wide-area operational coverage. When engaging a target, it performs a steep dive of up to 45 degrees at speeds reaching 150 km/h, ensuring rapid and precise impact. Built from lightweight foam-board materials, the S10s is optimized for fast, large-scale production during operations. Furthermore, its modular open-architecture design, aligned with the K-MOSA concept, allows mission payloads to be quickly swapped and integrated, delivering exceptional flexibility and interoperability in real combat environments.

Thermostatic Temperature switches

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

[Cutting by water jet] Micro water jet cutting: The micro water jet enables a refined process to be carried out in precision cutting. This high-precision technology reduces the jet diameter by a factor of 5 and makes water jet cutting more precise by a factor of 10. The micro water jet achieves a cutting accuracy of +/- 0.01 mm and a positioning accuracy of ±0.005 mm. The proven advantages of the cold cutting process remain unchanged. In the pure water process, the cutting width was reduced to 0.2 mm in the abrasive process for hard materials such as nickel-based alloys and titanium. The new technology controls the cutting process and manipulates the cutting path depending on the contour and speed enabling a highly precise cut. Standard waterjet cutting: Water jet cutting is highly efficient and at the same time less severe than other cutting techniques. Low process forces and thermal loads prevent bending or melting. We can cut filigree delicate contours from practically all nickel alloys and titanium alloys. Using our standard process we can cut a range of shapes and dimensions according to customer requirements and drawings and achieve tolerances of +/- 0.1 mm or +/- 0.2 mm.

Connectors

Live Video Sharing: Stream real-time video to remote experts for instant troubleshooting. AR Annotation: Remote experts can overlay AR markers and annotations directly onto the worker's view. Multi-User Collaboration: Multiple participants can join for a seamless remote teamwork experience. Multi-Device Compatibility: Available on PCs, tablets, smartphones, and smart glasses (VisionX) for maximum flexibility.