Spring loaded High Frequency Micro-D Coax Connectors (MDHC) offer low VSWR up to 40 GHz (typ). These connectors have a constant 50 ohm airline impedance interface and are 30% smaller than our SCX coaxial connectors.

Our LiDAR uses a custom-designed laser that separates 1064 nm and 532 nm wavelengths from a single source, with two dedicated receivers capturing each set of data independently. Inside the system, the linear laser beam is refracted at a 10-degree angle through a prism to enable circular scanning. An RF module is also integrated for real-time equipment status monitoring. From circuit board design to component selection, every part of this system was developed in-house by multiple institutions. As a result, we have successfully eliminated reliance on foreign technology.

This system product is a product that directly supplies and heats lubricant oil for smooth operation of the main engine cylinder’s metallic and mechanical movement. Lubricator, a product that supplies lubrication directly to the main engine cylinder liner, can control injection timing and consumption using an electronic control method that responds to the movement of the main engine piston. The alpha lubricator system is based on an algorithm controlling the cylinder oil dosage proportionally to the sulphur content in the fuel and, fuel consumption on particular load of engine. Minimum cylinder oil dosage is required to provide an adequate oil film and detergency properties. Everllence and WIN GD engines are currently applying the second generation Lubricator type, the Everllence type is Mk-I and the WIN GD type is Mk-ε (Epsilon).

Engine Start Begins with ATS. The Air Turbine Starter (ATS) is a key component of an aircraft's secondary power system, driven by Bleed Air supplied from the Auxiliary Power Unit (APU) to accelerate the engine up to approximately 8,900 RPM, enabling engine start. Through the in-house development and localization of the ATS, we have incorporated power generation, optimal design of the shear section with consideration of failure, Containment functionality, as well as lubrication and power transmission systems. In addition, we have secured manufacturing and assembly technologies and continue development aimed at successful operation and the establishment of a mass production system.

CoaXPress enables bidirectional transmission of data transfer, camera control, power supply (PoCXP), and triggering over a single coaxial cable. This product supports the following transmission standards. Designation Bit Rate ========== ======== CXP-1 1.250 Gbps CXP-2 2.500 Gbps CXP-3 3.125 Gbps CXP-5 5.000 Gbps CXP-6 6.250 Gbps CXP-12 12.500 Gbps The CXR-4C amplifies and transmits image signals from 1/2/4-channel CoaXPress cameras to a PC frame grabber. Typically, transmission matches the distance between the camera and the device. Transmission distance depends on the coaxial cable type, and due to significant variability, specific distances are not provided.  4 CH x 1 Camera Configuration  2 CH x 2 Camera Configuration  1 CH x 4 Camera Configuration  2 CH + 1CH Camera Configuration

Ultisense™ is Safran Vectronix’s line of high-performance OEM sensing modules, including ultra-compact Laser Rangefinders (LRF) and Digital Magnetic Compasses (DMC). Designed for seamless integration into military and civilian systems, they offer exceptional accuracy, ruggedness, and Swiss precision. LRF modules measure distances up to 30 km with ±1 m accuracy, while DMC modules provide azimuth accuracy down to 0.25°, even under extreme shock and environmental conditions.

Engineering Design Assistance Material Research & Development Manufacturing

Battlefield's Quick Disconnect technology is a leader in the UAV industry, and is now expanding expanding into ground defense vehicles. With over one million hours of successful flight time, Battlefield's quick disconnects have proven exceptional reliability even in extreme environments. EnduroLink by Battlefield has become the global standard UAV quick disconnects, widely applied across small to mid-sized UAV platforms worldwide. Fully customizable integrated design is available, including materials, size, and various end connect options even in the most demanding conditions.