ORSKOREA’s cylindrical grinding machines are engineered to deliver superior surface quality and tight tolerances for high-value parts. They are widely used in aerospace, defense, automotive, medical, and electronics industries for components that demand both strength and precision—such as engine shafts, landing gear parts, gears, and bearings. Key Advantages • Handles diverse, small-batch productions with consistent repeatability • Exceptional dimensional precision for tight-tolerance parts • Supports tapered and curved surface grinding • Flexible workpiece capacity with swing up to 350 mm • Smooth table movement with low noise and vibration for stable operation By combining precision, versatility, and long-term reliability, ORSKOREA’s cylindrical grinders provide manufacturers with the performance needed to meet mission-critical requirements.

AI Navigation Algorithm The Certus Mini range features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. The algorithm was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS The Certus Mini range contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Reliability The Certus Mini range has been designed from the ground up for mission-critical control applications where reliability is essential. Built using a safety-oriented real-time operating system, all software is designed and tested to high safety standards with fault-tolerance in mind. The Certus Mini range is designed, manufactured and tested to military standards. L1/L5 Multi Constellation RTK GNSS The Certus Mini D supports L1/L5 dual frequencies, and GPS, GLONASS, Galileo, BeiDou and NavIC constellations. Access to multiple constellations and frequencies provides enhanced accuracy, availability and performance even in difficult environments such as multi-storey urban canyons. The GNSS receiver has 10 mm position accuracy with real-time RTK or post-processed PPK. Dual Antenna Heading The Certus Mini D provides a high accuracy heading solution using two GNSS antennas. The Certus Mini D rapidly and consistently maintains an accurate heading without the need for magnetic calibration and is unaffected by magnetic interference. Additionally, the system can determine heading while stationary. This makes it well-suited to applications where there is limited, or no, positional movement.

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

This hydraulic tool package product is an ultra-high-pressure tool product used to assemble and disassemble major parts that make up the engine, and has been supplied to domestic and overseas engine customers since our foundation. The composition consists of a hydraulic pump, a hydraulic jack, a hydraulic hose, and a coupler, and supplies one package per ship. The product model can be selected according to the required pressure for each engine type and model.

The L-band 8-channel filter bank receiver module is equipped with eight internal filter bank channels, enabling improved reception performance by isolating specific sub-bands within the receive frequency range. A 100W limiter at the input stage protects the receiver from high-power signals, and the module offers a low noise figure of 3.0 dB or less. The input P1dB for the receiver is -20 dBm, and the module features a built-in path self-test function.

0.8m급 고해상도 초소형 지구관측 위성으로, 군집운용을 통해 고빈도 · 정밀 감시체계를 구축합니다. SpaceEye-M is a small satellite to produce high-resolution image data. A constellation of SpaceEye-M can perform precise monitoring over a large area with high revisit.

With more than 33,000 delivered to date, CFM56® engines mainly power single-aisle commercial jets from Airbus and Boeing. The CFM56®, developing 18,500 to 33,000 lb of thrust, set a standard in this market. It owes its impressive success to exceptional performance and reliability, the result of the two partners' technical excellence.

K2 online mall