With expertise in manufacturing guidance, navigation, and control (GNC) products, we have been used in over 2,000 spacecraft. Adaptable for size, moment, and power to meet optimal system requirements. Redundant windings available. Current, speed, and torque control. Simple digital interface to the spacecraft bus. Hermetically sealed. Long demonstrated lifetimes. ISO 14644-1 state-of-the-art cleanroom facility. ISO 9001:2015 certified.

24-7 non-stop operating RADAR for ceaseless aerial surveillance and early trajectory detection. Design and Manufacture - Antenna Housing - Driving Unit

EFFECTIVE RANGE : 600 m RIFLING : 1:7" Twist, 6 Groove R/H MAGAZINE CAPACITY : 30 rounds

Side shells, wing shells and fuselage structures are made of CFK, GFK, aluminium or organic sheets and get connected during production. Sealants are used to seal the connection surfaces. These are usually two-component polysulphides, which have to be applied in different geometries. Typical applications are: Fillet sealings, oversealings, interface sealings and seal caps. Due to their properties, polysulfides require very low pressure and shear handling. The compressibility of the fillers contained in the medium requires a high level of expertise and a coherent overall system from material removal to application. With manual application, long production times and high material ejection have a negative influence on the complete process. Complex quality standards are required due to the risk of human error. With the in-house developments of the vipro-DUOMIX from ViscoTec, this process can be depicted fully automatically. The individual nozzle design is also adapted to each application. The result is a controlled dosage in compliance with the specifications and at the same time the highest repeat accuracy.

It is a system that performs missions such as monitoring, surveillance and reconnaissance by ejecting and launching a foldable fixed-wing drone from the canister(tube) launcher. It is equipped with EO/IR Cameras (Electro-Optical / Infra-Red), which are mission equipment for reconnaissance, so that effective day and night image information can be collected. The gathered image information is transmitted to the ground control system (GCS) in real time while detecting and tracking the target by applying AI-based image processing technology. The foldable fixed-wing UAV has a simple structure and light weight, so it can be stored and transported in the canister launcher, and can be operated immediately so that it can be operated without time delay, and if necessary, the air vehicle can be retrieved and re-used by using a net-type recovery system.

Features ▪ Xilinx Zynq-7000 Series ARM-Cortex-A9 Core ▪ 10/100/1000 Ethernet Interface ▪ General-Purpose Input/Output ▪ SDLC Interface ▪ RS-232 Interface ▪ VPX 3U Form Factor ▪ Wedge lock, Plug-in Design ▪ Customized Rear I/O Pin Map

With a peak torque of >200Nm / 1770 lbf-in and a rated torque of 80Nm / 708 lbf-in, the fully redundant DA 58-D is the strongest, electromechanical, fully integrated (actuator control electronics, position sensing, motor and drivetrain in one housing) actuator in the market. Besides the well-proven redundant RS 485 interface, the DA 58-D also features a redundant CAN bus interface. The DA 58-D has been developed for applications with the highest reliability demands. The redundant – two channel – design of the actuator allows continuous operation even if one of the two channels has failed. All major components such as the electric motors, control and communication electronics, and power supply are available twice (redundant). The actuator features a triple-redundant position sensor (2 out of 3 voting). Additionally there are several sensors integrated to provide diagnostic information such as current consumption, supply voltage levels and temperature readings. All major components of the actuator are continuously diagnosed by the microcontrollers of the actuator and its health status can be read via the redundant RS485 / CAN interface.

For : Elevator Assembly Tool A320 Project 3.5m (L) x 1.5m (W) x 2m (H )